確認工業冷水機供電正常，無反相、缺相現象;冷卻塔風機、冷卻水泵、冷凍水泵均為獨立控制。開機前應確認電源正常，無反相、缺相現象。檢查工業冷水機主機、水泵、閥門、儀表及各種配件是否能正常打開，是否完好。檢查工業冷水機組油位是否正常

   開機前12小時接通冷水機組電源，使油加熱器順利電加熱;啟動冷水機前，先對冷凍水循環系統和冷卻水循環系統進行調試;檢查制冷系統壓力表讀數是否等于制冷劑在當地環境溫度下的飽和壓力值;檢查壓縮機電機絕緣電阻，絕緣電阻應在3兆歐以上。

   對工業冷水機組的回水溫度進行調節和設定后，機組就可以按照設定的溫度自動運行。一旦回凍水溫度達到設定溫度，在擰緊時主動停止制冷量調整，機組制冷量降低，直至停止。冷水機制造商推薦的冷凍水溫度范圍。分離蒸發器的冷凍水溫度允許為5℃，返回蒸發器的冷凍水溫度允許為25℃。建議冷凍水出口溫度為7-12℃，溫升5℃